Sensors and Solenoids

Coolant Temp Sensor - Large Thread 3/8 NPT 18TPI. Includes: Matching Delphi plug and pins. Notes: 127 deg C (260 F) Max reading. Part number: H...

Coolant Temp Sensor - 1/8 NPT Thread. Includes: Matching male Deutsch DTM-2 Connector (HT-031000) Notes: 127 deg C (260 F) Max reading. Part num...

Air Temp Sensor - Large Thread 3/8 NPT 18TPI Includes: Matching Delphi plug and pins. Notes: 127 deg C (260 F) Max reading.Part number: HT-010202

Plug and Pins Only - Suit Flex Fuel Composition Sensor. Suits: GM Flex Fuel Sensors. Includes: Plug + Pack of 3 pins.Part number: HT-011001

Haltech - 250 PSI Motorsport Fuel/Oil/Wastegate Pressure Sensor (Stainless Steel Diaphragm) Thread: 1/8 NPT.Haltech Map sensors are used in the som...

Haltech - 5 Bar Motorsport MAP Sensor (Stainless Steel Diaphragm) Thread: 1/8 NPT.Haltech Map sensors are used in the some of the worlds quickest v...

Haltech - 7 Bar "TI" MAP Sensor Thread: 1/8 NPT.Haltech Map sensors are used in the some of the worlds quickest vehicles, it is not hard to see why...

Haltech - 5 Bar "TI" MAP Sensor Thread: 1/8 NPT.Haltech Map sensors are used in the some of the worlds quickest vehicles, it is not hard to see why...

Haltech 3 Bar GM MAP Sensor.Haltech Map sensors are used in the some of the worlds quickest vehicles, it is not hard to see why these sensors are r...

Haltech 1 Bar GM MAP Sensor.Haltech Map sensors are used in the some of the worlds quickest vehicles, it is not hard to see why these sensors are r...

Suits: NTK Sensor Includes: Dual Channel, CAN Wideband Controller, 2 x NTK Sensors, CAN Cable (4'/1200mm), Power Supply Cable, 2 x Weld-on Bung, ...

CO2 Boost Control Dual Solenoid & Pressure Sensor Kit. Includes: Two 3 port 33Hz boost control solenoid kits, 150 PSI "TI" wastegate pressure s...

Idle Air Control Kit - Haltech Billet. Diameter: 10mm (3/8") Includes: Matching plugs and pins. Part number: HT-020305

Idle Air Control Valve - Bosch BAC/PWM 2 port. Suits: 19mm 3/4") ID hose. Includes: Matching plugs and pins. Notes: 2 Pin connection. Can be used w...

Nissan Attesa 4WD TPS Adaptor. Outputs: Produces the correct scaled TPS output signal required for the MFD and Attesa 4WD functions when using a st...

Analogue Output Adaptor. Outputs: Converts a PWM Output to 0-5v Analogue Signal. Suits: e.g for use with Evo 10 AWD controller. Includes: HT-031016...

Knock Sensor Suits 2014 Pro Tuner "Knock Ears" Kit Part number: HT-070105

Pro Tuner Knock Ears Kit 2014 Included: Two x 2 wire knock sensors with AMP style connector. Single 3 wire knock sensor lead with shield for conne...

Ideal for racers who want to log and analyse linear position of moving components like suspension travel, steering angle or gearbox position. Suits...

Linear Position Sensor - 1/2" - comes in a range of 100mm/150mm/200mm/250mm.Full list below:1. HT-011211 100mm Travel Length: Between Mounting Hole...

Linear Position Sensor - 1/2" - comes in a range of 5omm/100mm/150mm/200mm/250mm.Full list below:1. HT-011201 50mm Travel Length: Between Mounting ...

Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. Th...

Donut style 8mm Knock Sensor prewired with loom, flying leads. Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Li...

KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock senso...

For use with low-impedance injectors. Compatible with injectors with impedance between 2 and 6 Ohms. Please contact us if you are planning on using...

Small Diameter Trigger wheel – Medium and Large sizes also available.  24 tooth 150mm diameter 40mm centre

Medium Diameter Trigger wheel – Small and Large sizes also available. 24 tooth 175 diameter 40mm centre

Large Diameter Trigger wheel – Small and Medium sizes also available. 60-2 tooth 200mm diameter 40mm centre

Stainless Steel thread adapter, M10 x 1 Female to 1/8 BSP Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 BSP threaded ports.

Stainless Steel thread adapter, M10 x 1 Female to 1/8 NPT Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 NPT threaded ports.

Used in conjunction with a trigger wheel to measure crank angle, a vital measurement for engine operation. Can be used with almost any steel trigge...

High Pressure sensor for Liquid. Use for Fuel, Clutch, Brake etc. 140 Bar/2030PSI 45degree cone seat M10x1 Thread Includes mating connector kit T...

Throttle Position Sensor. Supports clockwise and counter-clockwise installations. 6 wire flying lead. Wiring instructions are provided in the box.F...

Donut style 8mm hole Includes plug and pin kit 

Hall effect sensor designed for use in applications where ferrousedge detection/near zero speed sensing is needed. They provide a sinking current o...

Two sensors in one - Combined 10 bar (145 psi) Liquid Pressure sensor and -40 to 140 deg C L Liquid Temperature sensor. Suitable for Oil, Cool...

Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8" NPT Thread

Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8" NPT Thread

Weld in Steel Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flange.

Weld in Aluminium Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flan...

This Link MAP sensor reads up to 3 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 2.0 B...

The Link 2.5 Bar MAP sensor reads up to 2.5 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up...

The Link 1.15 Bar MAP sensor reads up to 1.15 Bar absolute pressure. This means it is suitable for use in naturally aspirated engines. This MAP sen...

The Link 6.5 Bar MAP sensor reads up to 6.5 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up...

The 5 Bar MAP Variohm Eurosensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running...