Engine Management

Dual Switch Panel Only - includes Yellow knob. Includes: Dual panel and yellow adjustment knob. Notes: 12 Position Rotary Trim Modules are NOT i...

Triple Switch Panel Only - includes Yellow & Red knobs Includes: Triple panel and yellow and red adjustment knobs. Notes: 12 Position Rotary...

12 Position Rotary Trim Module - (Boost/Fuel/Ign etc) Triple Switch Panel Only - includes Yellow & Red knobs Includes: Triple panel, yellow ...

12 Position Rotary Trim Module - (Boost/Fuel/Ign etc) Dual Switch Panel Only - includes Yellow knob Includes: Dual panel, yellow adjustment knob a...

A selection of pre designed, semi transparent labels to suit the backlit Haltech CAN Keypads. Suits: Haltech CAN Keypads Includes: 5 Label Sheet ...

CAN Cable - DT to DTM Adaptor- Suits CAN Keypad. Suits: CAN Keypad 2 x 4 and 3 x 5 Includes: 1 x HT-130045 - Adaptor HarnessLength: 200mm Notes: ...

Suits: NTK Sensor Includes: Dual Channel, CAN Wideband Controller, 2 x NTK Sensors, CAN Cable (4'/1200mm), Power Supply Cable, 2 x Weld-on Bung, ...

Choose from the following options: Part Number HT-020039 - HPI6 - High Power Igniter - 15 Amp Six Channel Flying Lead Kit - Length: 2.0m (78"). P...

Water proof Elite USB Cap Only (Supplied as a pair) Suits: Elite ECUs (excluding Elite Pro Plug-in) Includes: Two water proof caps. Part number: H...

Mounting bracket for G4+ & G4X Atom & Monsoon (MTB2)

Mounting bracket for G4+ Thunder.

Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. Th...

Donut style 8mm Knock Sensor prewired with loom, flying leads. Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Li...

KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock senso...

E-Throttle Accelerator Pedal Module Firewall mounted hanging design 16degree (~70mm) travel Redundant dual output potentiometers suitable for use ...

Link's external E-throttle (Drive by Wire) module works with all Link's G4X ECUs (except the entry level AtomX), plus all G4+ ECUs (Storm and above...

Extreme Duty Fast Response EGT Temperature Probe  Type K thermocouple probe Exposed sensing junction for fastest response Includes 316 SS adjustab...

This sensor can be used with all wide band controllers and ECU’s that support LSU 4.9 sensors. This includes: Link G4+/G4X Fury and G4+Thunder ECU...

This three channel igniter is suitable for electronic ignition applications.  Required when using coils that don't have inbuilt igniters.Common use...

Dual core screen cable for use with trigger signals and knock sensors - 10m per pack

5 m long 'B' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connec...

5 m long 'A' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connec...

0.4m long 'A' loom to suit G4, G4+ and G4X Wire-In ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ E...

0.4m long 'B' loom to suit G4, G4+ and G4X Wire-In ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ E...

The G4+ KnockBlock is an essential tool for tuning and can aid in the early detection of incorrect ignition timing, lean air/fuel mixtures and mech...

Deutsch 3 Way Plug Kit

Blanking plugs for unused terminal positions - 10 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors.

Bosch 3 Way Plug Kit

7 way Bosch Style Plug, pin and Boot

Deutsch 2 Way Plug Kit

Bosch 2 way plug kit. Useful for a variety of applications. Most commonly paired with Bosch Fuel Injectors.Includes 2 way Bosch Style Plug, pins an...

Blanking plugs for unused terminal positions - 100 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors

Blanking plugs for unused terminal positions - 20 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors

Terminals - 20 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors.

Housing and 26 terminals for D connector. Plug and Pin kit only.Suitable for: G4+ Thunder

Equivalent plug and connectors as "B" Loom. Plug and Pin Kit only.Suitable for: Link G4X Storm (Loom A/Pin Kit A also required) Link G4X and G4+ F...

Housing and 26 terminals for C connector. Plug and Pin Kit Only.Suitable for: G4+ Thunder Obsolete G4 Atom and Lightning. (Not G4+ or G4X Atom)

Equivalent plug and connectors as "A" Loom. Plug and Pin Kit only.Suitable for:  All Link G4X WireIn ECU’s (Note: Loom B/Pin Kit B will also be re...

Deutsch DTM4 Connector Kit (Male) to create your own looms. DTM4 Male housing. Includes wedgelock and sockets.

Link CAN Connector to flying leads. Can be used for custom applications – Please contact our tech support to check compatibility/suitability. 

USB Mini Cable. Used to connect ECU to computer for tuning. Suitable for: G4X Atom G4X Monsoon G4+ Atom G4+ Kurofune G4+ Monsoon

Required to add CAN communication to WireIn ECU's which have CAN accessible via the Header.   Compatible ECU's:G4X/G4+ Atom (CAN1)G4X/G4+ Monsoon (...

Link CAN to Serial (DB9 Female connector) Tuning Cable. Used to connect ECU to a computer with a serial interface (DB9 Male). A USB tuning cable is...

2.5 m long 'A' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU conn...

2.5 m long 'A' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU conn...

Link ECU CAN Keypad Inserts are used for your CAN keypad, the keypads themselves arrive empty and you are to purchase buttons from these listings.

Link ECU CAN Keypad Inserts are used for your CAN keypad, the keypads themselves arrive empty and you are to purchase buttons from these listings.

Link ECU CAN Keypad Inserts are used for your CAN keypad, the keypads themselves arrive empty and you are to purchase buttons from these listings.