Engine Management and Accessories

Suits: Bosch LSU 4.9 Sensor Includes: Single Channel, CAN Wideband Controller, 4.9LSU Sensor, CAN Cable (4'/1200mm), Power Supply Cable, Weld-on ...

Link’s CAN Lambda is an easy to use CAN module that provides digital wideband sensor control via CAN bus and is compatible with leading aftermarket...

We have developed a complete DBW kit to swap out that cable old throttle and laggy throttle pedal in your Nissan R Chassis to install new electroni...

Includes: GPS Speed Input Module & GPS Antenna Matching male DTM-3 Connector and pins  

Suits: Nexus Series devices Includes: 1 x Bosch LSU 4.9 Sensor, 1 x HT-010726 - Adaptor Harness (1.2M), 1 x Weldable Bung Notes: Plug and Play wi...

Suits: NTK Sensor Includes: Single Channel, CAN Wideband Controller, NTK Sensor, CAN Cable (4'/1200mm), Power Supply Cable, Weld-on Bung, Quick S...

TCA-8 (4+4) Eight Channel Thermocouple Amplifier Programmed as TCA-4A and TCA-4B SUITS: Elite Series or Platinum Series ECU's INCLUDES:  Ei...

**LEAD TIME OF APPROXIMATELY 8 WEEKS** Syltech 2 wire sensor Idle Air Control Valve ( IACV ). Allows for remote idle control in any application usi...

Native Turbosmart E-gate control limited to Elite and Nexus Series ECU's Platinum Series not supported with this unique function, but outputs will ...

WB2 - Dual Channel CAN O2 Wideband Controller Kit, Smaller, lighter and water-proof! The new Haltech Wideband Controller can now be safely fitted i...

NTK Wideband hardware pack Includes sensor, weld in bung and 1.2M / 47" harness. Suits: Nexus Series devices Includes:  1 x NTK LZA08-H5 Sensor ...

Extreme Duty Fast Response EGT Temperature Probe  Type K thermocouple probe Exposed sensing junction for fastest response Includes 316 SS adjustab...

Suits: NTK Sensor Includes: Dual Channel, CAN Wideband Controller, 2 x NTK Sensors, CAN Cable (4'/1200mm), Power Supply Cable, 2 x Weld-on Bung, ...

Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. Th...

Donut style 8mm Knock Sensor prewired with loom, flying leads. Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Li...

KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock senso...

E-Throttle Accelerator Pedal Module Firewall mounted hanging design 16degree (~70mm) travel Redundant dual output potentiometers suitable for use ...

Link's external E-throttle (Drive by Wire) module works with all Link's G4X ECUs (except the entry level AtomX), plus all G4+ ECUs (Storm and above...

Extreme Duty Fast Response EGT Temperature Probe  Type K thermocouple probe Exposed sensing junction for fastest response Includes 316 SS adjustab...

This sensor can be used with all wide band controllers and ECU’s that support LSU 4.9 sensors. This includes: Link G4+/G4X Fury and G4+Thunder ECU...

This three channel igniter is suitable for electronic ignition applications.  Required when using coils that don't have inbuilt igniters.Common use...

The G4+ KnockBlock is an essential tool for tuning and can aid in the early detection of incorrect ignition timing, lean air/fuel mixtures and mech...